Presser Feet Customization Test.1

So a hundred dollars later and small game of web-phone-word.of.mouth-tag the problem with the Brother’s presser feet, is now in the process of being fixed (or at least slowed down). As it may have been mentioned before the presser feet collection for this machine (the Brother DB2-B791-015) have come from an older Singer 600WI, which is a standard drop feed – straight stitch industrial sewing machine. Therefor the presser feet are not slotted for the motion of the needle feed style mechanism that the Brother uses. The everyday foot (of a needle feed machine) has a longer slot and a wider opening to allow the needle to pass through on it’s down motion, while it is pulling the fabric back (this foot was ordered from a company in Hopkinsville, Kentucky by the name of Dunlap Sunbrand). Some of the old feet had been customized by using a Dremel tool, which can also be done by leaving your old presser feet with a good sewing shop that you trust. However, after grinding down a bunch of material from two of the cheaper feet that the Brother uses, it was clear that although it may get the job done, it is time consuming and slightly, well, maybe, mmm, too inaccurate, for industry quality taste and expectations. This of course brings up the issue of the right tool for the job, which should always be taken advantage of when you can. Thus introducing the milling machine. It was obvious that in order to have the feet correctly modified it would take the expertise of a machinist and their milling machine to precisely cut through the feet from the underside and then widen and elongate the slot for the needle to pass through. Some of the concerns were that the cut would have to be, A) in the correct spot (obviously) in relationship not to the usual “hole” that a presser foot has for the needle to rise and fall through, but in relationship to where the presser foot is mounted to the needle bar, this is because, as close as each foot is to the next in terms of needle to foot, each one is slightly different due to human error, so it is of most importance to consider where the needle bar and receiving end of the presser foot meet because this is going to be the most consistent juncture. Next, B) that it was of the correct dimensions, of course this too is fairly obvious, but the interesting thing is that on the Brother, it consistently places the needle towards the right-inside of the presser foot opening. So no matter how wide the gap is, for somereasont he right side is always too close, the problem of that leads into section C. Here is the largest concern of the customization of the feet, C) in sewing we must consider the materials that are being used, in this particular sense it would primarily consist of cotton, polyester, and nylon, and then any combination of those three and beyond (rayon, silk, wool, vinyl, hemp, leather, solar sheeting, etc. etc.), with the largest issue being abrasion. For sewing – abrasion may be the biggest antibody that exsists. Every time you run a stitch or seam the thread is passed through numerous holes and entry ways, not to mention the fabric which it is mending together. For the Brother and it’s feet the big C has to deal with the fact that the cuts or millwork has to leave it with no burs. It is extremely important that when all is said and done at the end of the day, that the presser feet are completely smooth in any area where the thread or material may come into contact with them. In some tests of the feet which were retro-fitted with the Dremel tool, the thread would sometimes split sue to microscopic burs int he edge of the foot where the thread was rubbing everytime it passed up and down. This is very important, in all areas of the machine, the needle plate, the presser feet, the needles, the bed of the machine, the table which holds all of this, must be as smooth and free of burs, splinters, or anything else that may catch the materials and cause a tear. Just think about things being smooo-th and you should be alright. With the right people and the right tools, all of the cuts should be very very easy to smooth out, unlike the many different ridges and vertexes that result from the Dremel tool bit (which is not always the case, but the right tool for the job won in this situation).

While we wait for the newly composed feet to come back from the machine shop…

H.R. Slater Co. Inc 2050 West 18th Street Chicago, IL 60608 tel. 312/666/1855 c/o Bob

which was recommended by Frank at Ecker-Erhardt Co. 2347 West 18th Street Chicago, IL 60608 tel. 312/226/6030

with Frank being mentioned by John at Mechanical Engineering Products Company Inc. 1319 West Lake Street Chicago, IL 60607 tel. 312/421/3375

…here are two images of four presser feet for a Singer 111 model needle feed machine (that were found at Eddy Sewing Machine in Los Angeles). Unfortunately they have a different way of syncing up to the machines needle bar, so they are of no use to the Brother DB2-B791-015. But they give a clear example of the exaggerated cuts and wider stance that the slot for a needle feed machine presser foot needs. From the left, number 1and 3 are the best example, number 2 and 4 are probably just like Linko 211 and 212 presser feet – for the inside radius of a jean pocket.

Comments are closed.